JDSU FVDi-2400光纤端面检测仪的安装和调试步骤介绍
Published on2026-04-02
JDSU FVDi-2400光纤端面检测仪（现属VIAVI Solutions旗下）是一款专业用于光纤端面检测的设备，其安装和调试步骤对于确保检测精度和设备正常运行至关重要。以下是详细的安装和调试步骤：JDSU FVDi-2400硬件安装固定主机根据使用场景，台式使用时需贴紧防滑垫，机柜安装则使用随机附带的耳片和M6螺钉进行固定，确保面板水平，避免探头线缆折弯。连接电源首先连接DC端，再接入市电，观察指示灯红绿切换，表示已完成待机状态。若无市电，可并联12V锂电池，注意极性正确。安装探头将探头航空头的“红点”对准主机PROBE口的“红点”，直推到底后旋紧外套环，避免空旋或暴力插拔。选配适配器根据被测连接器型号，安装相应的陶瓷套管，扭矩控制在0.2 N・m，防止过紧导致裂痕或过松导致成像偏移。插入SD卡将SD卡推入右侧卡槽，听到“咔嗒”声表示已到位，用于保存截图和报告，电脑读取时可直接拔卡。JDSU FVDi-2400光学调试开机自检长按电源键2秒，等待Viavi Logo出现并倒计时5秒，若提示“Probe Error”，则需重新插拔探头。白平衡校准扣上白色校准帽，依次进入Menu→设置→白平衡→确认，屏幕闪烁2秒后显示“OK”即完成校准。对焦操作插入参考跳线，按“FAST/SLOW”键调至120×倍率，微调镜头环至纤芯与陶瓷边界最清晰，对焦值显示绿色“√”；若模糊则检查套管是否装反或裂口。照明调整进入Menu→高级→照明，查看四角照度；若单侧发暗，使用无水乙醇棉签轻擦LED透镜，避免直接用手接触。保存基准图在洁净参考跳线对焦完成后，按“保存→设为基准”，后续检测可叠加黄金图进行比对缺陷。
Key Words：JDSU FVDi-2400FVDi-2400FVDi-2400光纤端面检测仪
Copyright and Disclaimer
1.This website reprints content from external sources (not from Shenzhen Haochen Electronic Technology) and clearly indicates the original source. The purpose of such reproduction is for informational exchange only and does not imply endorsement of the views expressed therein, nor does it assume responsibility for the accuracy or authenticity of the content. The website shall not bear any direct or joint liability for infringement arising from the use of such materials.
2.Any media outlets, websites, or individuals reprinting content from this website must retain the original source attribution as specified herein and assume full legal responsibility for copyright compliance and any related intellectual property matters.
3.If the article involves issues such as content or copyright, you may contact the publisher to offer your opinions or request its removal. Alternatively, you need to contact us within one week from the date of publication. Otherwise, it will be regarded as the waiver of relevant rights.