安捷伦Agilent 86140B光谱分析仪操作流程
Published on2026-03-27
安捷伦Agilent 86140B是款台式标准性能光谱分析仪，主要用于 50GHz 及更宽的 WDM 系统、光源和宽带组件的表征。以下就是Agilent 86140B的操作流程。Agilent 86140B操作流程开机与准备1.开机顺序：依次打开仪器背面的5个电源开关（编号1-5），每两个开关间隔约20秒，避免电流冲击。2.预热：开机后至少预热30分钟，确保光学和电子系统稳定，保证测量精度。3.检查环境：确保仪器周围无强电磁干扰，电源稳定，并确认氩气瓶气压在2-3MPa范围内，低于此值需及时更换。校准操作AutoAlign校准：在以下情况必须执行：仪器被移动后长时间未使用（超过5天）测量结果出现异常波动校准通过仪器内置菜单中的“Align”功能启动，过程约需数分钟，期间避免震动或操作。设置测量参数1.波长范围：默认设置为1530–1570nm，适用于C波段DWDM系统测试。可根据需求调整至全范围600–1700nm。2.分辨率带宽（RBW）：可调至60pm（高分辨率模式）或10nm（快速扫描模式）。3.扫描模式：普通扫描：频率设为1kHz深度扫描：灵敏度可达-85dBm，适合低功率信号检测。光源与测量模式选择1.进入“SourceTests”功能，根据被测光源类型选择：SLED（超辐射发光二极管）DFB（分布反馈激光器）FP（法布里-珀罗激光器）2.启动“AutoMeas”功能进行自动全波段扫描，波形稳定后系统将自动记录：中心波长峰值功率光谱宽度（如FWHM）数据输出与接口使用VGA接口：连接外部显示器，实时监控屏幕内容。Centronics（并行）接口：打印彩色测量结果。GPIB接口：用于远程控制和高速数据传输至PC。软盘驱动器 + 打印机：可直接保存测量文件并打印报告。关机流程1.按与开机相反的顺序关闭背面5个电源开关（5→1）。2.两次开关机之间间隔至少20分钟，防止元器件热损伤
Key Words：Agilent 86140B86140B86140B光谱分析仪
Copyright and Disclaimer
1.This website reprints content from external sources (not from Shenzhen Haochen Electronic Technology) and clearly indicates the original source. The purpose of such reproduction is for informational exchange only and does not imply endorsement of the views expressed therein, nor does it assume responsibility for the accuracy or authenticity of the content. The website shall not bear any direct or joint liability for infringement arising from the use of such materials.
2.Any media outlets, websites, or individuals reprinting content from this website must retain the original source attribution as specified herein and assume full legal responsibility for copyright compliance and any related intellectual property matters.
3.If the article involves issues such as content or copyright, you may contact the publisher to offer your opinions or request its removal. Alternatively, you need to contact us within one week from the date of publication. Otherwise, it will be regarded as the waiver of relevant rights.